Andrews Motorcycle Cams

Cam,W/O Gear Grind # Tw37B Twin Cam 00/L 5 Speed Models Stock Springs Andrews.288137

• Want more power for your Twin Cam 88 Engine?
• Andrews Products has eight proven cam grinds to get you there
• More horsepower and torque for stock or modified engines is within easy reach
• All cam grinds listed are designed for use with stock HD hydraulic lifters

Note: (*) Timing and duration listed for .053 cam lift.Andrews
Application: Hot Street Cams for 88 or 95 inches. 80+ rear wheel horsepower possible with well tuned 88 incher, more with 95. Smooth idle, broad torque. (2200-5600RPM) 9.0 to 9.5 CR
Grind: TW37b
Timing(*): 18/38, 46/14
Duration: .053 - 236, 240; .020 - 272, 276
Valve Lift: .510, .510
Lift @ TDC .174, .148
Springs: Stock

Cams, Andrews Tw54 Bt 99/06 Except 06Dyna Stock Springs

• Want more power for your Twin Cam 88 Engine?
• Andrews Products has eight proven cam grinds to get you there
• More horsepower and torque for stock or modified engines is within easy reach
• All cam grinds listed are designed for use with stock HD hydraulic lifters

Note: (*) Timing and duration listed for .053 cam lift.Andrews
Application: New in 2008! Specially designed for 95 inch + engines with CR up to 10:1 (2200-5600 RPM)
Grind: TW54
Timing(*): 16/42, 43/15
Duration: .053 - 238, 238; .020 - 273, 273
Valve Lift: .555, .555
Lift @ TDC: .165, .158
Springs: Stock

Cams, Andrews Tw 31S Bt 99/06 Except 06 Dyna Stock Springs

• Want more power for your Twin Cam 88 Engine?
• Andrews Products has eight proven cam grinds to get you there
• More horsepower and torque for stock or modified engines is within easy reach
• All cam grinds listed are designed for use with stock HD hydraulic lifters

Note: (*) Timing and duration listed for .053 cam lift.Andrews
Application: Great Cam for motors with 95 and 9.8 to 10.2 CR. Lower TDC lift for easy installation. Similar to TW37 with different timing. (2400-5600 RPM)
Grind: TW31s
Timing(*): 10/46, 52/08
Duration: .053 - 236, 240; .020 - 272, 276
Valve Lift: .510, .510
Lift @ TDC: .131, .120
Springs: Stock

Andrews 09H Camshafts Twin Cam 2007/Later* Uw Stock Springs

• Camshafts on all new 2007/Later Twin Cam engines and 2006 Dyna Glides use roller chain cam drives
• Cams made for 1999/2006 engines will not fit the 2007/Later (or 2006 Dyna engines)
• All earlier Twin Cam engines run older type cam drive chains
• Designed for use with stock H/D hydraulic lifters

(*) Timing and duration listed for .053 cam liftAndrews
More Power through entire RPM range (1000-5400)
09H Grind
Timing: (-02/28) int, (40/-04)exh
CL 105 int, 112 exh
Duration .053 - 206 int, 216 exh, .020 242 int, 252 exh
Valve lift .492 int, .486 exh
Lift @ TDC .075
Stock springs

Cams, Andrews 55H Twin Cam 2007/Later* High Lift Springs

• Camshafts on all new 2007/Later Twin Cam engines and 2006 Dyna Glides use roller chain cam drives
• Cams made for 1999/2006 engines will not fit the 2007/Later (or 2006 Dyna engines)
• All earlier Twin Cam engines run older type cam drive chains
• Designed for use with stock H/D hydraulic lifters

(*) Timing and duration listed for .053 cam liftAndrews
Great cam for 96 inch engines with 9.8 to 10.2 CR. Max horsepower and torque at mid & upper RPMs (2600-6200 RPM)
55H Grind, 22/46 & 52/20 Timing(*), 102 & 106 CL, 248 & 252 Duration .053, 283 & 292 Duration .020, .550 & .550 Valve Lift, .197 & .181 Lift @ TDC, Hi-Lift Springs

Cams, Andrews 50H Twin Cam 2007/Later* Stock Springs

• Camshafts on all new 2007/Later Twin Cam engines and 2006 Dyna Glides use roller chain cam drives
• Cams made for 1999/2006 engines will not fit the 2007/Later (or 2006 Dyna engines)
• All earlier Twin Cam engines run older type cam drive chains
• Designed for use with stock H/D hydraulic lifters

(*) Timing and duration listed for .053 cam liftAndrews
Designed for easy installation in 96 inch motors with stock heads and 9.5 to 9.8 CR (2400-6000 RPM)
50H Grind, 20/48 & 54/18 Timing(*), 104 & 108 CL, 248 & 252 Duration .053, 283 & 287 Duration .020, .510 & .510 Valve Lift, .184 & .168 Lift @ TDC, Stock Springs

Cams, Andrews 54H Twin Cam 2007/Later* Stock Springs

• Camshafts on all new 2007/Later Twin Cam engines and 2006 Dyna Glides use roller chain cam drives
• Cams made for 1999/2006 engines will not fit the 2007/Later (or 2006 Dyna engines)
• All earlier Twin Cam engines run older type cam drive chains
• Designed for use with stock H/D hydraulic lifters

(*) Timing and duration listed for .053 cam liftAndrews
New in 2008! Specially designed for 96 & 103 engines with CR up to 10:1 (2200-5600 RPM)
54H Grind, 16/42 & 43/15 Timing(*), 103 & 104 CL, 238 & 238 Duration .053, 273 & 273 Duration .020, .555 & .555 Valve Lift, .165 & .158 Lift @ TDC, Stock Springs

Cams, Andrews 37H Twin Cam 2007/Later* Stock Springs

• Camshafts on all new 2007/Later Twin Cam engines and 2006 Dyna Glides use roller chain cam drives
• Cams made for 1999/2006 engines will not fit the 2007/Later (or 2006 Dyna engines)
• All earlier Twin Cam engines run older type cam drive chains
• Designed for use with stock H/D hydraulic lifters

(*) Timing and duration listed for .053 cam liftAndrews
Hot street cams for 96 or 103 inches. 80+ rear wheel horsepower possible with well tuned 88 incher, more with 95. Smooth idle, broad torque (2200-5600 RPM) 9.0 to 9.5 CR
37H Grind, 18/38 & 46/14 Timing(*), 100 & 106 CL, 236 & 240 Duration .053, 272 & 276 Duration .020, .510 & .510 Valve Lift, .174 & .148 Lift @ TDC, Stock Springs

Cams, Andrews 32H Twin Cam 2007/Later* High Lift Springs

• Camshafts on all new 2007/Later Twin Cam engines and 2006 Dyna Glides use roller chain cam drives
• Cams made for 1999/2006 engines will not fit the 2007/Later (or 2006 Dyna engines)
• All earlier Twin Cam engines run older type cam drive chains
• Designed for use with stock H/D hydraulic lifters

(*) Timing and duration listed for .053 cam liftAndrews
High lift version of 31H. Much more power thru RPM range with 10:1+ compression pistons (2800-5600 RPM)
32H Grind, 10/46 & 52/08 Timing(*), 108 & 112 CL, 236 & 240 Duration .053, 272 & 276 Duration .020, .570 & .570 Valve Lift, .131 & .120 Lift @ TDC, Hi-Lift Springs

Cams, Andrews 31H Twin Cam 2007/Later* Stock Springs

• Camshafts on all new 2007/Later Twin Cam engines and 2006 Dyna Glides use roller chain cam drives
• Cams made for 1999/2006 engines will not fit the 2007/Later (or 2006 Dyna engines)
• All earlier Twin Cam engines run older type cam drive chains
• Designed for use with stock H/D hydraulic lifters

(*) Timing and duration listed for .053 cam liftAndrews
Great cam for motors with 96 and 9.8 to 10.2 CR. Lower TDC lift for easy installation. Similar to TW37 with different timing. (2400-5600 RPM)
31H Grind, 10/46 & 52/08 Timing(*), 108 & 112 CL, 236 & 240 Duration .053, 272 & 276 Duration .020, .510 & .510 Valve Lift, .131 & .120 Lift @ TDC, Stock Springs

Cams, Andrews 26H Twin Cam 2007/Later* Stock Springs

• Camshafts on all new 2007/Later Twin Cam engines and 2006 Dyna Glides use roller chain cam drives
• Cams made for 1999/2006 engines will not fit the 2007/Later (or 2006 Dyna engines)
• All earlier Twin Cam engines run older type cam drive chains
• Designed for use with stock H/D hydraulic lifters

(*) Timing and duration listed for .053 cam liftAndrews
Bolt-in cam 96 to 103 and stock compression ratio.
Great for two up touring, this cam will add torque and horsepower at lower and middle RPM ranges (1800-5200 RPM)
26H Grind
Timing: (11/35) int, (41/09)exh
CL 102 int, 230 exh
Duration .053 - 226 int, 266 exh, .020 262 int, 490 exh
Valve lift .490 int, .112 exh
Lift @ TDC .138
Stock springs

Cams, Andrews 21H Twin Cam 2007/Later* Stock Springs

• Camshafts on all new 2007/Later Twin Cam engines and 2006 Dyna Glides use roller chain cam drives
• Cams made for 1999/2006 engines will not fit the 2007/Later (or 2006 Dyna engines)
• All earlier Twin Cam engines run older type cam drive chains
• Designed for use with stock H/D hydraulic lifters

(*) Timing and duration listed for .053 cam liftAndrews
Bolt-in Cam: More torque for all around riding with heavy bikes, stock compression ratios and stock pistons. Similar to #23 Cam for EV80. (1700-4800 RPM)
21H Grind, 10/30 & 40/08 Timing(*), 100 & 106 CL, 220 & 228 Duration .053, 255 & 264 Duration .020, .498 & .498 Valve Lift, .134 & .121 Lift @ TDC, Stock Springs

Cam & Gear Set N2 Grind Spt Evo 883,1100 & 1200,91/99 Bolt In Andrews 298125
A camshaft upgrade is the most logical step after air filter, exhaust, carburetor, and ignition system improvements have been made. It will improve mid and upper-end power. All camshafts listed are ground with stock size base circle and can be used with stock push rods. Instructions included.

Cam Specifications - with stock 1.43:1 rocker arm ratio

Cam Grind	Valve Timing	Duration @ .053	Duration @ .020	Valve Lift	Overlap @ .053	Lobe Centerline	Lobe Separation Angle	TDC Lift at Valve
Q stock (76/85)	10/32 35/07

Cam & Gear Set Y Grind Ih Spt 71/80 Mid/Upper Range Power Bolt In Andrews 214080
A camshaft upgrade is the most logical step after air filter, exhaust, carburetor, and ignition system improvements have been made. It will improve mid and upper-end power. All camshafts listed are ground with stock size base circle and can be used with stock push rods. Instructions included.

Cam Specifications - with stock 1.43:1 rocker arm ratio

Cam Grind	Valve Timing	Duration @ .053	Duration @ .020	Valve Lift	Overlap @ .053	Lobe Centerline	Lobe Separation Angle	TDC Lift at Valve
Q stock (76/85)	10/32 35/07

Cam & Gear Set Y Grind Ih Spt 57/70 Mid/Upper Range Power Bolt In Andrews 214075
A camshaft upgrade is the most logical step after air filter, exhaust, carburetor, and ignition system improvements have been made. It will improve mid and upper-end power. All camshafts listed are ground with stock size base circle and can be used with stock push rods. Instructions included.

Cam Specifications - with stock 1.43:1 rocker arm ratio

Cam Grind	Valve Timing	Duration @ .053	Duration @ .020	Valve Lift	Overlap @ .053	Lobe Centerline	Lobe Separation Angle	TDC Lift at Valve
Q stock (76/85)	10/32 35/07

Cam,W/Gear Viper Plus 565Vp Big Twin Evo All Years* Hyd Or Mech Power House 565Vp
Dyno proven POWER HOUSE cams for maximum performance. rom bolt in, for more all around performance and touring, to .620 lift for those ground pounding street and strip machines.Hydraulic or Solid Lifters--This is a hotter version of our popular viper cam. Has a sophisticated profile fast intake ramp with slower closing ramp for maximum cylinder fill. Requires springs with a minimum of 175/190lbs. seat pressure. Perfect combination with high compression 10:1 plus compression 80 Cl and smalll stroker. Provides very strong upper mid range with 6500 RPM top end power. Use with mild to wild ported heads, good free flowing exhaust, performance carb and ignition and dig in for the ride of your life. Valve Lift .565. TDC Lift (at valve) In. .209 Ex. .189. Duration (degrees) In. 258 Ex 258. Timing @ .053 24/54 58/20. Grind Viper Plus 565VP.

Cam,W/Gear Ev27 Grind Big Twin Evo All Years Hydraulic Andrews.291127
Time tested and track proven Andrew's cams have computer enhanced design features that provide a superior combination of performance gains and reliability without sacrificing component longevity. Installation instructions included. Timing and Duration measured at .053 cam lift.

Listed for reference: 1984/1987/Later OE cam is 212° intake, 202° exhaust, .472 lift on both valves. Timing 03/39 54/02. Valve lift .495 .495. Duration 222 236. Grind OEM (L) 1988/1991.

Listed for reference: 1992/Later OE cam very close to 1984/1987 specs. California cams are approximately 178° duration. uel injected 0 cam is 200° duration intake and 216° duration exhaust.Bolt-in street cam with fast open and close ramps. Similar timing to EV3 but designed to produce a very broad torque band. Pulls 1500 to 6000 RPM. USE STOCK SPRINGS. EI or Carb. Timing 20/36 44/16. Valve Lift .495 .495. Duration 236 240. Grind EV27.Note: Always replace the INA brand cam bearing with our Torrington brand cam bearing 66922.

Cam,W/Gear Ev46 Grind Big Twin Evo All Years Hydraulic Andrews.291146
Time tested and track proven Andrew's cams have computer enhanced design features that provide a superior combination of performance gains and reliability without sacrificing component longevity. Installation instructions included. Timing and Duration measured at .053 cam lift.

Listed for reference: 1984/1987/Later OE cam is 212° intake, 202° exhaust, .472 lift on both valves. Timing 03/39 54/02. Valve lift .495 .495. Duration 222 236. Grind OEM (L) 1988/1991.

Listed for reference: 1992/Later OE cam very close to 1984/1987 specs. California cams are approximately 178° duration. uel injected 0 cam is 200° duration intake and 216° duration exhaust.Bolt-in performance cam with fast open and close ramps. Similar to EV3 but higher static compression pressure for 6000+RPM with stock heads and hydraulic lifters. USE STOCK SPRINGS. Timing 25/41 49/17. Valve Lift .495 .495. Duration 246 246. Grind EV46.Note: Always replace the INA brand cam bearing with our Torrington brand cam bearing 66922.

Cam,W/Gear Ev13 Grind Big Twin Evo All Years Hydraulic Andrews.291113
Time tested and track proven Andrew's cams have computer enhanced design features that provide a superior combination of performance gains and reliability without sacrificing component longevity. Installation instructions included. Timing and Duration measured at .053 cam lift.

Listed for reference: 1984/1987/Later OE cam is 212° intake, 202° exhaust, .472 lift on both valves. Timing 03/39 54/02. Valve lift .495 .495. Duration 222 236. Grind OEM (L) 1988/1991.

Listed for reference: 1992/Later OE cam very close to 1984/1987 specs. California cams are approximately 178° duration. uel injected 0 cam is 200° duration intake and 216° duration exhaust.Bolt-in cam for street or touring use with more mid range and upper end power. Much more stuff that stock '88 or '92 EV cam. Especially effective in reducing oil temperatures. USE STOCK SPRINGS. EI or Carb. Timing 15/31 45/13. Valve Lift .485 .495. Duration 226 238. Grind EV13.Note: Always replace the INA brand cam bearing with our Torrington brand cam bearing 66922.

Cam,W/Gear Ev23 Grind Big Twin Evo All Years Hydraulic Andrews.291123
Time tested and track proven Andrew's cams have computer enhanced design features that provide a superior combination of performance gains and reliability without sacrificing component longevity. Installation instructions included. Timing and Duration measured at .053 cam lift.

Listed for reference: 1984/1987/Later OE cam is 212° intake, 202° exhaust, .472 lift on both valves. Timing 03/39 54/02. Valve lift .495 .495. Duration 222 236. Grind OEM (L) 1988/1991.

Listed for reference: 1992/Later OE cam very close to 1984/1987 specs. California cams are approximately 178° duration. uel injected 0 cam is 200° duration intake and 216° duration exhaust.Bolt-in mild street cam that produces more torque and horsepower for all around riding when used in 80 cubic inch engines with the standard 8.5 to 1 compression ratio. This cam pulls strong between 1800/5200 RPM. USE STOCK SPRINGS. EI or Carb. Timing 10/20 40/08. Valve Lift .498. Duration 220 228. Grind EV23.Note: Always replace the INA brand cam bearing with our Torrington brand cam bearing 66922.

Cam,W/Gear Ev51 Grind Big Twin Evo All Years Hydraulic Andrews.291151
Time tested and track proven Andrew's cams have computer enhanced design features that provide a superior combination of performance gains and reliability without sacrificing component longevity. Installation instructions included. Timing and Duration measured at .053 cam lift.

Listed for reference: 1984/1987/Later OE cam is 212° intake, 202° exhaust, .472 lift on both valves. Timing 03/39 54/02. Valve lift .495 .495. Duration 222 236. Grind OEM (L) 1988/1991.

Listed for reference: 1992/Later OE cam very close to 1984/1987 specs. California cams are approximately 178° duration. uel injected 0 cam is 200° duration intake and 216° duration exhaust.Easy installation with longer duration for modified street engines with hydraulic lifters. Power range from 3000/6500 RPM. USE STOCK SPRINGS. Timing 28/44 54/22. Valve Lift .510 .510. Duration 252 256. Grind EV51.Note: Always replace the INA brand cam bearing with our Torrington brand cam bearing 66922.

Gr Drive Camshafts,Andrews 37G Tc 99/L 5 Speed Mdls,Uw #66018 And #66019 Kits 288137G

• Andrews
• These bolt-in type cams are designed for 88ci Twin Cam engines with stock compression using hydraulic lifters
• They are compatible with carbureted or fuel injected models. Note: EI models will require re-calibration of the ECU
• Reduced maintenance (no plastic chain guides or tension shoes to wear and contaminate your engine oil or clog oil passages)
• Cam timing remains constant. All drive and cam gears utilize a light press fit (gear lash) thus eliminating any chain stretch
• Bearing loads are reduced. No spring loaded chain tensioners are used (which can rob up to 4 horsepower)
• Critical sprocket alignment is unnecessary
• Can be used with the OEM non-adjustable pushrods, but we suggest using our adjustable pushrods found in the Engine Section to ease installation and eliminate the need to remove the fuel tank and rocker covers
• See General Merchandise Section for the required installation tools
• Includes instructions

37G Grind Cams
Designed to produce a broad torque band with horsepower in the 80+ range if used with low restriction exhaust and a free flow air filter
Pulls best between 2200/5800 RPM
See Miscellaneous Information for Cam SpecificationsCam Specifications
with stock 1.625:1 rocker arm ratio

Cam Grind

Gr Drive Camshafts,Andrews 26G Tc 99/L 5 Speed Mdls,Uw #66018 And #66019 Kits .288126G

• Andrews
• These bolt-in type cams are designed for 88ci Twin Cam engines with stock compression using hydraulic lifters
• They are compatible with carbureted or fuel injected models. Note: EI models will require re-calibration of the ECU
• Reduced maintenance (no plastic chain guides or tension shoes to wear and contaminate your engine oil or clog oil passages)
• Cam timing remains constant. All drive and cam gears utilize a light press fit (gear lash) thus eliminating any chain stretch
• Bearing loads are reduced. No spring loaded chain tensioners are used (which can rob up to 4 horsepower)
• Critical sprocket alignment is unnecessary
• Can be used with the OEM non-adjustable pushrods, but we suggest using our adjustable pushrods found in the Engine Section to ease installation and eliminate the need to remove the fuel tank and rocker covers
• See General Merchandise Section for the required installation tools
• Includes instructions

26G Grind Cams
Designed for two-up riding on heavier bikes, pulling a trailer or when using a sidecar. These cams produce much more torque and horsepower at the lower and middle RPM range
Pulls best between 1800/5500 RPM
See Miscellaneous Information for Cam SpecificationsCam Specifications
with stock 1.625:1 rocker arm ratio

Cam Grind

Cam,W/Gear A2 Grind Shovelhead 1970/Early 1977 Hyd Or Mech Andrews 212263

• Whether you want a better street cam for a stock motor, a big lift cam for a hotrod bike, or something in between then these cams are what you are looking for
• All of these cams are computer designed and precision ground from alloy steel billet
• Timing and Duration measured at .053 cam lift

Note: 1948/1957 Panhead models require engine case machining for installation of a 1958/1984 style cam shaft needle bearing

Note: Rocker arm ratios are as follows, Panhead 1.5:1, Shovelhead 1.43:1. 1980/1981 Shovelhead motors with anything higher than a valve lift of .430 will require valve guide to top spring collar clearancingAndrews
Application: Street/Drags - Bolts into Shovelhead (except 1980/1981) with no head work. More mid-range & high end power. Idle smoothness unaffected.
Timing: Intake 19/43, Exhaust 50/18
Duration: Intake 242, Exhaust 248
Grind: A2, Year: 1970/Early 1977
Valve Lift: Shovelhead .450, Panhead .470

Cam,W/Gear A2 Grind Pan & Shovelhead 1948/1969 Hyd Or Mech Andrews 212260

• Whether you want a better street cam for a stock motor, a big lift cam for a hotrod bike, or something in between then these cams are what you are looking for
• All of these cams are computer designed and precision ground from alloy steel billet
• Timing and Duration measured at .053 cam lift

Note: 1948/1957 Panhead models require engine case machining for installation of a 1958/1984 style cam shaft needle bearing

Note: Rocker arm ratios are as follows, Panhead 1.5:1, Shovelhead 1.43:1. 1980/1981 Shovelhead motors with anything higher than a valve lift of .430 will require valve guide to top spring collar clearancingAndrews
Application: Street/Drags - Bolts into Shovelhead (except 1980/1981) with no head work. More mid-range & high end power. Idle smoothness unaffected.
Timing: Intake 19/43, Exhaust 50/18
Duration: Intake 242, Exhaust 248
Grind: A2, Year: 1948/1969
Valve Lift: Shovelhead .450, Panhead .470

Cam, W/Gear C Grind Big Twin 48/69 Mechanical Andrews 212600

• Whether you want a better street cam for a stock motor, a big lift cam for a hotrod bike, or something in between then these cams are what you are looking for
• All of these cams are computer designed and precision ground from alloy steel billet
• Timing and Duration measured at .053 cam lift

Note: 1948/1957 Panhead models require engine case machining for installation of a 1958/1984 style cam shaft needle bearing

Note: Rocker arm ratios are as follows, Panhead 1.5:1, Shovelhead 1.43:1. 1980/1981 Shovelhead motors with anything higher than a valve lift of .430 will require valve guide to top spring collar clearancingAndrews
Application: Best cam made for big street engines. Strokers from 84 to 96 inches will really turn on with this cam. Broad torque band from 2000-7000+ RPM.
Timing: Intake 37/61, Exhaust 61/37
Duration: Intake 278, Exhaust 278
Grind: C, Year: 1948/1969
Valve Lift: Shovelhead .525, Panhead .550

Cam W/ Gear C Grind Shovelhead Late 1977/1984 Mechanical Andrews 212620

• Whether you want a better street cam for a stock motor, a big lift cam for a hotrod bike, or something in between then these cams are what you are looking for
• All of these cams are computer designed and precision ground from alloy steel billet
• Timing and Duration measured at .053 cam lift

Note: 1948/1957 Panhead models require engine case machining for installation of a 1958/1984 style cam shaft needle bearing

Note: Rocker arm ratios are as follows, Panhead 1.5:1, Shovelhead 1.43:1. 1980/1981 Shovelhead motors with anything higher than a valve lift of .430 will require valve guide to top spring collar clearancingAndrews
Application: Best cam made for big street engines. Strokers from 84 to 96 inches will really turn on with this cam. Broad torque band from 2000-7000+ RPM.
Timing: Intake 37/61, Exhaust 61/37
Duration: Intake 278, Exhaust 278
Grind: C, Year: Late 1977/1984
Valve Lift: Shovelhead .525, Panhead .550

Cam W/Gear C Grind Shovelhead 1970/Early 1977 Mechanical Andrews 212610

• Whether you want a better street cam for a stock motor, a big lift cam for a hotrod bike, or something in between then these cams are what you are looking for
• All of these cams are computer designed and precision ground from alloy steel billet
• Timing and Duration measured at .053 cam lift

Note: 1948/1957 Panhead models require engine case machining for installation of a 1958/1984 style cam shaft needle bearing

Note: Rocker arm ratios are as follows, Panhead 1.5:1, Shovelhead 1.43:1. 1980/1981 Shovelhead motors with anything higher than a valve lift of .430 will require valve guide to top spring collar clearancingAndrews
Application: Best cam made for big street engines. Strokers from 84 to 96 inches will really turn on with this cam. Broad torque band from 2000-7000+ RPM.
Timing: Intake 37/61, Exhaust 61/37
Duration: Intake 278, Exhaust 278
Grind: C, Year: 1970/Early 1977
Valve Lift: Shovelhead .525, Panhead .550

Cam With Gear, 7 Grind Shovelhead Late 1977/1984 Mechanical Andrews 212539

• Whether you want a better street cam for a stock motor, a big lift cam for a hotrod bike, or something in between then these cams are what you are looking for
• All of these cams are computer designed and precision ground from alloy steel billet
• Timing and Duration measured at .053 cam lift

Note: 1948/1957 Panhead models require engine case machining for installation of a 1958/1984 style cam shaft needle bearing

Note: Rocker arm ratios are as follows, Panhead 1.5:1, Shovelhead 1.43:1. 1980/1981 Shovelhead motors with anything higher than a valve lift of .430 will require valve guide to top spring collar clearancingAndrews
Application: Hotter version of a B grind. Great street cam especially for 84ci/88ci strokers. Maximum torque available from 2500-6500 RPM.
Timing: Intake 29/53, Exhaust 59/27
Duration: Intake 262, Exhaust 266
Grind: 7, Year: Late 1977/1984
Valve Lift: Shovelhead .510, Panhead .535

Cam, W/Gear Bh Grind Big Twin 70/77 Hydraulic Andrews 212430

• Whether you want a better street cam for a stock motor, a big lift cam for a hotrod bike, or something in between then these cams are what you are looking for
• All of these cams are computer designed and precision ground from alloy steel billet
• Timing and Duration measured at .053 cam lift

Note: 1948/1957 Panhead models require engine case machining for installation of a 1958/1984 style cam shaft needle bearing

Note: Rocker arm ratios are as follows, Panhead 1.5:1, Shovelhead 1.43:1. 1980/1981 Shovelhead motors with anything higher than a valve lift of .430 will require valve guide to top spring collar clearancingAndrews
Application: Hydraulic version of a B cam. Usually a bolt-in spring spacing may be required on Shovelheads 1980/1981.
Timing: Intake 24/52, Exhaust 52/24
Duration: Intake 256, Exhaust 256
Grind: BH, Year: 1970/Early 1977
Valve Lift: Shovelhead .450, Panhead .470

Cam, W/Gear Bh Grind Big Twin 48/69 Hydraulic Andrews 212420

• Whether you want a better street cam for a stock motor, a big lift cam for a hotrod bike, or something in between then these cams are what you are looking for
• All of these cams are computer designed and precision ground from alloy steel billet
• Timing and Duration measured at .053 cam lift

Note: 1948/1957 Panhead models require engine case machining for installation of a 1958/1984 style cam shaft needle bearing

Note: Rocker arm ratios are as follows, Panhead 1.5:1, Shovelhead 1.43:1. 1980/1981 Shovelhead motors with anything higher than a valve lift of .430 will require valve guide to top spring collar clearancingAndrews
Application: Hydraulic version of a B cam. Usually a bolt-in spring spacing may be required on Shovelheads 1980/1981.
Timing: Intake 24/52, Exhaust 52/24
Duration: Intake 256, Exhaust 256
Grind: BH, Year: 1948/1969
Valve Lift: Shovelhead .450, Panhead .470

Cam,W/Gear Bh Grind Shovelhead Late 1977/1984 Hydraulic Andrews 212440

• Whether you want a better street cam for a stock motor, a big lift cam for a hotrod bike, or something in between then these cams are what you are looking for
• All of these cams are computer designed and precision ground from alloy steel billet
• Timing and Duration measured at .053 cam lift

Note: 1948/1957 Panhead models require engine case machining for installation of a 1958/1984 style cam shaft needle bearing

Note: Rocker arm ratios are as follows, Panhead 1.5:1, Shovelhead 1.43:1. 1980/1981 Shovelhead motors with anything higher than a valve lift of .430 will require valve guide to top spring collar clearancingAndrews
Application: Hydraulic version of a B cam. Usually a bolt-in spring spacing may be required on Shovelheads 1980/1981.
Timing: Intake 24/52, Exhaust 52/24
Duration: Intake 256, Exhaust 256
Grind: BH, Year: Late 1977/1984
Valve Lift: Shovelhead .450, Panhead .470

Cam W/Gear B2 Grind Shovelhead Late 1977/1984 Mechanical Andrews 212358

• Whether you want a better street cam for a stock motor, a big lift cam for a hotrod bike, or something in between then these cams are what you are looking for
• All of these cams are computer designed and precision ground from alloy steel billet
• Timing and Duration measured at .053 cam lift

Note: 1948/1957 Panhead models require engine case machining for installation of a 1958/1984 style cam shaft needle bearing

Note: Rocker arm ratios are as follows, Panhead 1.5:1, Shovelhead 1.43:1. 1980/1981 Shovelhead motors with anything higher than a valve lift of .430 will require valve guide to top spring collar clearancingAndrews
Application: Street/Drags - Much more mid-range & high end power. Idle smoothness unaffected. The cam for modified 74ci/80ci & small strokers. Spring spacing required.
Timing: Intake 26/50, Exhaust 53/25
Duration: Intake 256, Exhaust 258
Grind: B2, Year: Late 1977/1984
Valve Lift: Shovelhead .485, Panhead .507