Lower End Tools

Cam/Crank Sprocket Lock Tool Twin Cam 07/L* Dyna 06/L* Jims 994

• Due to the radical new design of the Twin Cam, specialized tools are required to properly perform engine repair without damage
• All Jims tools are manufactured from top quality material and designed for years of trouble free service
• All tools include instructions

Jims
Camshaft/Crankshaft Locking Tool
Fits Twin Cam 2007/Later & Dyna 2006/Later
Precision tool allows the technician to lock the camshaft and crankshaft sprockets to properly remove, replace and torque the sprocket bolts. Tool is made non-marring delrin
Replaces HD# 42314

Oil Screen Plug Tool Bt L52/99 (Ex Tc)Tappet Plug 7/16" Dr W/O-Ring,Slot Design

• Low profile design (¹/₂ tall) allows access to the tappet screen plug on bikes with exhaust pipe interference
• Designed with an O ring on the ⁷/₁₆ hex to hold the tool in the box end wrench on socket
• Features a flange design that allows more downward force to be applied to the tool for stubborn plugs

Motion Pro
For Big Twin Late 1952/1999 with OEM style slotted plug (except Twin Cam), (Imported)

V-Twin Manufacturing 1986-up Primary Cap Installation Tool - Sold Each

Primary cap installation tool.

XL 1986-UP

V-Twin Manufacturing 79-Up XL 2.060 TimkenBrowng.Instl.Tool - Sold Each
Sprocket Shaft Timken Bearing Installer Tool. Year /Model: 1977-up Sportster Note: Sold separately for 1977-up use with 16-0149 & 16-1837.

V-Twin Manufacturing 1955-1969 Sprocket Shft JIMS Seal Wrench - Sold Each
Sprocket Shaft Seal & Lock Installers for Big Twins. Years/Application: 1955-69 Installs Nut & Seal (JIMS)

V-Twin Manufacturing Primary Drive Lock Tool w-Step - Sold Each
Big Twin Primary Drive Locking Tool is used as a wedge type device to hold the Primary drive gear while the proper torque is applied without damaging the Primary gear. Constructed of nylon, OEM# 41214.

DENNIS STUBBLEFIELD SALES Crankshaft Turning Tool, Black, made in the usa, Each, specific application, Harley 71-00 FX 64-99 FL 87 - 94 XL

• Rotates the crankshaft; may be used while engine is in or out of the frame
• Enables work on any part of the engine
• Slides over the left side of the splined crankshaft

DENNIS STUBBLEFIELD SALES Crankshaft Jam Tool, Black, made in the usa, Each

• Locks the crankshaft through the timing mark hole on the left
• Enables timing and camshaft work to be done without the crankshaft moving from the timing mark line

LANG TOOLS Crankshaft Bearing End Play Setup Tool, Black, made in the usa, Each

• For Big Twin engines to set up crankshaft bearing endplay
• Diameter of the bolt is turned slightly smaller than the actual crankshaft diameter, allowing the inner bearing races to be installed and removed without pressing them on or off
• Allows much faster changing of shims and faster setup time
• Made in the U.S.A.

JIMS Interconnect Seal Leak Testing Tool, Balancer Tension Plate, Blue, made in the usa, Each, specific application, Harley 00-15 FX 00-15 FL

• Checks sealing of interconnect seal H-D No.45359-00
• Seal is required to seal the oil passage way from right case to the balancer tensioner plate; leaking can cause over oiling of the lower end that decreases horsepower from oil drag
• Can also be used to check pressure lost at the balancer tensioner plate
• Made in the U.S.A.

FEULING OIL PUMP CORP. Pinion Shaft Run-Out And Gear Backlash Tool, Red, specific application, Harley 83-15 FX 84-15 FL 87 - 94 XL

• Makes for a great display to show and explain to customers the condition of their crankshaft
• Simplifies and speeds up the process of checking pinion shaft run out
• Quickly and accurately measures gear drive backlash on Twin Cam engines
• Mounts to cam chest side of engine case using designated mounting holes of tool combined with cam-cover bolt holes
• Includes tool plate, +/-0.001" dial indicator, thumb screws and hardware
• Made in the U.S.A.

JIMS Timken Case Bearing Tool, Black, Harley 03-10 FX 03-10 FL

• This tool is a must for the big-cubic-inch late-model Twin Cam engine builder
• It may also be used to replace bearings for stock 88" or 96" engines utilizing the special JIMS precision insert
• Easily and accurately converts the left side crankshaft roller bearing (OEM #24604-00D) to the more durable Timken Bearing (OEM #9028)
• Sleeve is several times stronger than stock aluminum case material that standard bearings ride in
• Included in kit is one new steel bearing insert sleeve (held to under .0002" total indicator reading), all necessary drill bits to drill oil feed and return holes, press plate that holds bearing sleeve insert in line with case bearing bore at time of installation, all necessary hardware and instructions
• Requires normal hand tools, hand drill and two-ton press
• Timken bearing not included; see PART #0924-0108
• Replacement Timken sleeve kit available separately
• Made in the U.S.A.

Primary Drive Lock Bar Tool Fxr & Flt 5 Spd All Years* Sprocket To Sprocket Jims.2317
Avoid damage to the primary driveline with one of these steel primary drive locking bars. Depending on application, use these tools to lock the clutch sprocket to the engine sprocket when the clutch or engine nuts are loosened or tightened. This will allow the proper use of a torque wrench. Saves time and money.

Note: Never use an impact wrench or loosening of the alternator magnets might occur.Jims
Fits FXR & FLT 5 speed, all years

Gear Cvr Bushing Dowel Pin Bt 36/L(Ex Tc88) K Spt 54/90 Replaces Hd #275
HARDWARE
Bushing Dowel Pin fits Big Twin 1936/Later (except Twin Cam)
Gear Cover Bushing Dowel Pin fits Shovelhead 1970/1984, Big Twin Evolution 1984/1999, K Model & Sportster 1954/1990
Also used on all bushings and designed to work with Jims bushing installer and drill jigs
Package of 5
Replaces HD# 275

Cam Bearing Remover Twin Cam 07/L* Dyna 06/L* Jims 993

• Due to the radical new design of the Twin Cam, specialized tools are required to properly perform engine repair without damage
• All Jims tools are manufactured from top quality material and designed for years of trouble free service
• All tools include instructions

Jims
Inner Cam Bearing Remover
Fits Twin Cam 2007/Later & Dyna 2006/Later
Blind hole puller will easily remove the crankcase needle bearing that supports the camshafts. The unique design prevents the pin rollers from accidentally falling into the crankcase that is known to happen when using inferior pullers

Gear Cover & Cam Seal Tool Bt 1970/L(Ex Tc 88)Remove W/O Removing Gear Cover Jims .2243

• Remove the cam seal without removing the cam cover
• Mount the tool, screw in the removal screws, rotate the center and out pops the seal
• Presses seal in square and flat for a no leak fit
• Simplifies cam cover removal from the engine case

Jims
or Big Twin 1970/Later (except Twin Cam)

Cam Assembly Tool Twin Cam 07/L* Dyna 06/L* Jims 990

• Due to the radical new design of the Twin Cam, specialized tools are required to properly perform engine repair without damage
• All Jims tools are manufactured from top quality material and designed for years of trouble free service
• All tools include instructions

Jims
Cam Assembly Tool
Use this tool to hold both cams in an upright position while lowering the cam support plate over both guides and cam journal guides. Tool has been manufactured from a non-marring material, that will not damage any of the cam's surfaces. Use on all Twin Cam 2007/Later & Dyna 2006/Later

Cam Bearing Tool Collar Only For All Twin Cams Jims 1278-3

• Due to the radical new design of the Twin Cam, specialized tools are required to properly perform engine repair without damage
• All Jims tools are manufactured from top quality material and designed for years of trouble free service
• All tools include instructions

Jims
Cam Bearing Installation Tool
Collar Only fits all Twin Cams
Tool will install the two inner cam needle bearings into the crankcase. It perfectly aligns to the shaft bores for a precision press fit

Bushing Installer & Drill Jig Bt 54/92 Gr Cvr Gr Shft Bshg Installer/#31 Drill..1013-54Tb
Not only has Jims come up with the best bushing installer available, but they have incorporated a drill jig into each tool for ease of pining the bushing after installation. This tool is so quick and easy it will pay for Fitself the first time you use it. All jigs include #31 drill bit. Jims
Installer/Drill Jigs
Fits Big Twin 1954/1992 gear cover gear shaft bushing
Replaces HD# 25582-54 & 25582-73

Bushing Installer & Drill Jig Bt 70/L(Ex Tc88)Gr Cvr Bushing Installer/#31 Drill..1012-70Tb
Not only has Jims come up with the best bushing installer available, but they have incorporated a drill jig into each tool for ease of pining the bushing after installation. This tool is so quick and easy it will pay for Fitself the first time you use it. All jigs include #31 drill bit. Jims
Installer/Drill Jig
Fits Big Twin 1970/Later (except Twin Cam) gear cover cam bushing
Replaces HD# 25581-70

Bushing Installer & Drill Jig Bt 36/69 Case/Gr Cvr Cam Bshg Installer/#31 Drill..1011-36Tb
Not only has Jims come up with the best bushing installer available, but they have incorporated a drill jig into each tool for ease of pining the bushing after installation. This tool is so quick and easy it will pay for Fitself the first time you use it. All jigs include #31 drill bit. Jims
Installer/Drill Jigs
Fits Big Twin 1936/1969 case and gear cover cam bushing
Replaces HD# 25581-36 & 25597-36

Case Splitter Tool Twin Cam 07/L* Dyna 06/L* Jims 995

• Easily removes crankshaft assembly from left case on Big Twin models
• This tool will also separate case halves that have tight sealant bond
• Includes instructions

Jims
Fits Twin Cam 2007/Later & Dyna 2006/Later

Crank Case Tool Bt 55/06 Dyna 99/05 Jims 1047-Tp

• Easily removes crankshaft assembly from left case on Big Twin models
• This tool will also separate case halves that have tight sealant bond
• Includes instructions

Jims
Fits Panhead 1955/1965, Shovelhead 1966/1984, Big Twin Evolution 1984/1999, Twin Cam 1999/2006 & Dyna 1995/2005

Balancer Shaft Removal Tool Fits All Softail Models 07/L* Used On Fr & Rr Shafts,Mfg#960

• Designed to remove both front and rear counter balance shaft assembly from the left engine case
• Use on both 96 and 110 Beta engines
• Use with 60760 installation tool
• Includes instructions

Jims
Fits Softail 2007/Later
Replaces HD# 48457

Engine Rotator Tool Big Twin 6 Speed 2006/Later* Rpls Hd-48283 Mfg#975

• Used to rotate the flywheel assembly when doing pushrod adjustments, building engines or when checking operating clearances such as piston or valve to valve
• Can also be used to hold the flywheel assembly from rotating when torquing the cam drive sprockets retention bolts
• Manufactured with a long socket design making it easier to use without a ¹/₂ drive extension on your ¹/₂ driver
• Includes instructions

Note: Not for use with pneumatic or electric impact; this tool is only guaranteed for use with hand driver - not impactsJims
Fits Big Twin 6 speed 2006/Later
Replaces HD# 48283

Balancer/Bearing Service Tool St 07/L*,Installs Shaft,Also Use To R&R Rh Bearings,Mfg#957

• The balancer shaft installation tool is used to align and safely install a new balancer bearing and counter balancer shaft into a Twin Cam 96 or 110 B Softail engine case
• Use our 60763 to remove the balancer shafts
• The right side bearing tool removes and installs the outboard balancer bearing on the chain guide support plate
• Includes instructions

Jims
Fits Softail 2007/Later
Balance Shaft Installation Tool Replaces HD# 48309 & Right side Bearing R&R Tool Replaces HD# 48474

Engine Tool,Puller Gear Cover Bt 1970/L(Ex Tc 88) Spt 71/L* Removes Gear Cover
This steel puller will easily remove a gear cover with zero chance of damage to an expensive chrome job or gasket surface. Motion Pro
Fits Big Twin 1970/Later (except Twin Cam) & Sportster 1971/Later

V-Twin Manufacturing Main Drive Gear Remover Tool - Sold Each
Main drive gear remover tool removes the main drive gear from the main bearing while in the transmission case. This eliminates the need of an arbor press and the risk of case damage. Fits: FXD 2006-UP FXST 2007-UP FLST 2007-

V-Twin Manufacturing JIMS 91-Up XL Adapter Screw - Sold Each
1990-up Big Twin Clutch Compressor Tool features access windows to ease the removal and installation of snap ring, by Jims. Fits: Adapter to fit 1991-up XL

V-Twin Manufacturing 1955-up JIMS Crank Assembly Removal Tool - Sold Each
Crank Assembly Removal Tool is used to press flywheels from cases, press cases apart and break sealant bond, for 1955-up Big Twin, by Jims.

V-Twin Manufacturing 1954-1976 JIMS Sprocket Shft Browng Tool XL - Sold Each
Sprocket Shaft Timken Bearing Installer Tool. Year /Model: 1954-76 Jims